FAQs

Roof Pitch Explained and Which Coverings Suit Your Pitch

What roof pitch means, why it limits which tiles, slates or sheets a roofer can fit, the published minimum pitches for common coverings and what to ask when a re-roof or extension has a low pitch.

Illustration of three house roofs at different angles with a protractor and stacks of tiles and slates

Pitch is the angle of your roof slope in degrees. Every tile or slate has a minimum pitch below which it should not be used. Natural slate needs 20 degrees for a moderate exposure roof using 500mm slates and a 115mm overlap. Plain concrete tiles need 35 degrees while some interlocking tiles can go as low as 12.5 degrees.

What is a roof pitch and how is it measured?

The pitch of your roof is the angle it makes against a perfectly flat horizontal line. A completely flat surface is zero degrees and a vertical wall is 90 degrees. Pitched roofs come in many angles.

To understand how this works it helps to have the parts of a roof explained plainly. The ridge is the horizontal peak at the very top of your roof. The eaves are the lower edges where the gutters sit. The rafters are the sloping structural timbers that run from the ridge down to the eaves. The pitch is the angle of those rafters.

A roof is rarely just two simple slopes. You might have hips which are the sloping outer corners where two sections meet. You might have valleys which are the internal sloping angles where two roof sections join. The verges are the outer edges of a roof above a gable wall. Different parts of your home can have different pitches. An extension or a dormer window in a loft conversion can have a different pitch from the main roof, and pitch matters for how an extension or loft conversion is designed.

You must never climb on your roof or use ladders at height to measure the pitch yourself. A professional roofer or a surveyor measures it safely. They will work out the exact angle for you. If you are planning an extension an architect will work it out for you and write the pitch on the building drawings.

Why pitch decides which covering you can have

Your roof fights a constant battle against the UK weather. Rain hits the roof and relies on gravity to reach the gutters. On a steep roof the water runs off rapidly. On a shallow roof the water moves much more slowly and has time to pool.

Wind complicates this by blowing rain back up the roof slope. To stop water getting in the tiles must overlap. This overlap is called the headlap. The headlap is the exact amount by which the tile above covers the tile below. If the wind blows rain up a shallow roof the headlap must be long enough to stop the water reaching the timber below.

Beneath the tiles sits the underlay. Underlay is often called felt or a membrane and it provides a secondary barrier against wind and rain. The tiles themselves are fixed to battens. Battens are the horizontal strips of timber nailed across your rafters. At the bottom of the roof the water runs off into the guttering. The guttering is attached to the fascias and soffits. Fascias are the vertical boards holding the gutters and soffits are the boards tucked underneath them. Lead flashing is the metal used to seal joints where the roof meets a brick wall or a chimney. The correct tile ensures water stays on the outside and never reaches the underlay, battens or flashing.

These factors decide the right covering for your pitch:

  • The exact angle of the roof slope in degrees
  • The type and shape of the tile or slate
  • The recommended headlap for the product
  • The length of your rafters from the ridge to the eaves

Minimum pitch for plain tiles and slate

The table below shows minimum pitches for common roofing materials. These figures are manufacturers' minimums, and the slate figure also appears in the standard BS 5534.

Covering

Minimum pitch

Plain concrete tiles

35 degrees

Clay tiles

15 to 40 degrees depending on the product

Concrete interlocking tiles

12.5 to 25 degrees depending on the product

Natural slate

20 degrees (depends on headlap)

Cedar shingles and shakes

14 degrees for shingles and 20 degrees for shakes

Treat these as a rough guide. Every product has its own exact limit, so ask the roofer to confirm it.

Plain concrete tiles need a minimum of 35 degrees. Concrete interlocking tiles range from 12.5 to 25 degrees depending on the product, and the figures 12.5, 15, 17.5, 22.5 and 25 degrees all appear.

Clay tiles vary widely depending on how they are manufactured. One product might have a minimum pitch of 15 degrees while another needs 30, 35 or even 40 degrees. You must ask the roofer to confirm the minimum pitch of the exact product quoted.

The minimum pitch for natural slate is 20 degrees. This is based on standard BS 5534 and assumes a moderate exposure area using a 500mm slate and a 115mm overlap. Fibre cement slate is a man-made alternative to natural slate, and the roofer should confirm the minimum pitch of the exact product.

Other materials have strict limits too. Corrugated garage roof panels need to be installed at a minimum pitch of 10 degrees for water to run off efficiently. If you are installing an integrated solar tile product one known product lists a minimum pitch of 20 degrees.

Low pitch roof tiles and what changes

A low pitch roof typically has a pitch between 10 and 30 degrees. The factors that affect minimum pitch include tile type, tile shape, recommended lap, rafter length and headlap.

The main change is the headlap. The headlap is typically increased from a 75mm minimum to 100mm for a low pitch roof. This extra overlap gives the rain further to travel if the wind blows it upwards. You should check the technical data sheets and ask the manufacturer if you are unsure about the required overlap.

Rafter length can also restrict some low pitch tiles. Ask whether the length of your rafters limits the product you have been quoted.

When a roof is classed as flat

Anything below 10 degrees is considered a flat roof, so the covering changes to a continuous waterproof layer.

There are several flat roof systems available. Built-up felt is usually torch-on felt applied with heat. EPDM rubber is a single sheet of synthetic rubber cut to size. GRP fibreglass is painted on to form a hard continuous shell. Single-ply is a durable plastic membrane and liquid coatings are rolled on to form a seamless finish.

These waterproof layers sit on a timber deck. The timber deck is the flat board structure that supports the roof. A warm roof has the insulation placed above this timber deck. A cold roof has the insulation placed between the timber joists below the deck. You can read more about these options in our guide to flat roof replacement cost.

What happens if a covering is used below its minimum pitch

A covering used below its minimum pitch can face higher risks of water getting in, wind uplift and condensation.

It may also invalidate product warranties, which is one more reason to check the data sheet and the manufacturer's certificates.

Whether building control approval is needed for a re-roof or an extension depends on the work, so ask your council or a registered building control approver before work starts.

Replacing a glazed or polycarbonate conservatory roof with a solid one takes the conservatory out of its exemption so building regulations apply to the new roof. Rules differ in Scotland and Northern Ireland so ask your council rather than guessing.

Who should measure your pitch

You should never measure the pitch yourself. A professional roofer or an architect will do this safely. Small repairs are usually a fixed price or a day rate. Larger work is priced per square metre plus access. Scaffolding is often a separate and significant line on the quote. Waste removal and VAT may or may not be included so you must ask. Prices are higher in London and the South East. Nobody can see rotten timber until the old covering is off so a good quote says how extras will be priced.

You must watch out for common mistakes and scams in this trade. Avoid cold callers who have spotted a loose tile or moss from the street. Walk away from pressure to decide today, cash only demands, big deposits and firms with no physical address. Reject vague one line quotes. Be wary of being sold a whole new roof for a local fault. Ignore roof coating and painting claims or pressure washing sold as maintenance. Guarantees are worthless if the firm folds because they are not insurance-backed.

Under the Consumer Rights Act 2015 work must be done with reasonable care and skill. If it is not you can ask for it to be put right or for money back. A quote is a fixed price but an estimate is not. Contracts agreed at home, by phone or online normally carry a 14-day cooling-off period. If you ask for work to start inside that period you must pay for what has been done. Paying by credit card gives Section 75 protection on purchases over £100 and up to £30,000. Citizens Advice is the place to go with a dispute.

CompetentRoofer is a government-authorised competent person scheme run by the National Federation of Roofing Contractors (NFRC). Registered roofers can self-certify roof refurbishment in England and Wales and the customer should receive a building regulations compliance certificate. Otherwise the work goes through council building control or a registered building control approver. TrustMark is the government-endorsed quality scheme for work in and around the home. Membership is a good sign but not a guarantee and you should check this on the scheme own register. Going without the building regulations certificate is a major problem when you sell your home.

Questions to ask your roofer before they start:

  • What is the exact pitch of my roof in degrees?
  • What is the manufacturer's minimum pitch for the tile you have quoted?
  • Will you need to increase the headlap to 100mm for this low pitch?
  • Does the length of my rafters restrict the use of this product?
  • Is the cost of scaffolding, waste removal and VAT included in this fixed quote?
  • Are you a member of CompetentRoofer or will we need to apply to building control?

Common questions

Is there a roof pitch calculator I can use?

You do not need to find a formula or a roof pitch calculator to work this out yourself. A professional roofer or an architect will work it out for you safely. They can measure it from the ground or read it directly from your building drawings.

What is the minimum roof pitch for a slate roof?

The standard minimum pitch for natural slate is 20 degrees. This figure applies to a moderate exposure area using a 500mm slate and a 115mm headlap. If your roof is shallower than 20 degrees, ask your roofer what covering suits it.

What are low pitch roof tiles?

A low pitched roof typically has a pitch between 10 and 30 degrees, and tiles for it are chosen for their low minimum pitch. The headlap is typically increased from 75mm to 100mm.

How do I know if my roof is flat or pitched?

If the angle of the roof slope is below 10 degrees the roof is treated as a flat roof. It will need a continuous waterproof membrane rather than overlapping tiles. Above 10 degrees, the covering depends on the exact pitch and product.

Next steps before a re-roof or extension

  1. Ask a professional roofer to measure your pitch safely from the ground or the loft.
  2. Ask the roofer to confirm the minimum pitch of the exact product quoted and check the data sheet.
  3. Take photos of any defects from the ground so you can discuss them without climbing a ladder.
  4. Get three written quotes that itemise scaffolding, waste removal and VAT.
  5. Check the roofer is registered with CompetentRoofer or apply to your local building control.
  6. Ask for proof of insurance, agree staged payments and release the final payment only when the job is finished.

Knowing your roof pitch helps you choose a covering that suits it. When you know what materials your roof can support you can find a roofer near you to provide a detailed written quote.

Find a top rated roofer near you

3,904 roofers across the UK, each ranked on their Google rating and the number of reviews behind it. Start with your county:

All counties and towns · The UK Top 100 roofers

Ann Walters
Written by
Ann Walters Editor

Anne is a writer and editor for Top Rated Roofers. When she's not writing guides and articles, she loves to do gardening, walk her dog Bobby, and read French novels.

Looking for a trusted roofer? Browse our verified listings.

Find a Roofer